For more info visit http://www.GreenFuelH2O.com
+++++++++++++++++++++++++++++++++++++++
A look at my new management system handling 21 LPM
Duration : 0:4:5
HHO-gas/20-lpm-hydrogen-generator-hho-managment-system#more-354″ class=”more-link”>Read the rest of this entry »
Chevrolet 2006 HHR Water For Fuel - HHO Gas Part 2
I am a perfectionist in doing things right the first time. During the demonstration I try to perform the demonstration as if everyone is watching the video was doing it themselves along with me. During my video I try to do things to prevent skepticism. Before I put this welding machine on a trial run on my vehicle I will be using scientific equipment to make sure that there is no sodium hydroxide passing through the tube on a regular basis into the engine. During the demonstration there was a 20 foot hose running from the welding machine to the flashback arrestor an additional 15 foot from the arrestor to the automobile. The flashback arrestor at that moment of time was acting as a fluid separator only allowing the HHO Gas pass through it. In addition I will be checking with the Chevrolet dealership electrical department to make sure that the alternator is putting out enough energy to run my electric inverter taking the power from DC to AC to run the welding device. If we cannot run the inverter to the welding machine that we will have to bypass the AC power supply on the welding machine and go into the DC portion of the machine to perform the same functions as if it was plugged into the AC. Before we do that we would try this simple way first using our inverter to simplify the installation.
Duration : 0:7:49
HHO Gas provides combustion for an engine without producing harful exhaust.
check out smacks booster design & a great (&free) PDF which explains everything:
smacksboosters.110mb.com/
smacks youtube:
youtube.com/user/EletrikRide
Duration : 0:7:9
HHO Gas provides combustion for an engine without producing harmful exhaust.
check out smacks booster design & a great (&free) PDF which explains everything:
smacksboosters.110mb.com/
smacks youtube:
youtube.com/user/EletrikRide
Duration : 0:9:20
First bench test of a new 21 plate Dry cell Xcel-21 By GenHydroSolutions Inc.
6×6 316L SS 20G custom stamped plates and Neoprene70 gaskets. 4n 3 4PP = 16 plates. Config P 4n N 4n P 4n N
Please visit my website at
www.gohydro2.com
for more information. (its under construction right now) You can find my dry cell kits currently on Ebay as well. Feel free to PM with any question comments.
Bench test details:
13.6v @ 30A took 30sec to make 1 liter of HHO which is 2lpm. efficiency =4.9mmw. I have had conditioned cells bench test at well over 5.8 mmw using more neutral plates config. I will do another video using 5N plates in a 25 plate cell same configuration to compare efficiencies in mmw.
What i like about 4n is the short time to get to operating temps and you can use less KOH/Ga. to get your amps.
I used 1 tblspoon of KOH/GA. temps were around 100F after 20 min run time. These cells will handle heat pretty good most get to about 140F ater about 5hours of run time at this amperage and can be air cooled to run at 120F.
Production should increase as cells are conditioned on this cell, to well over 2.5 lpm.
Duration : 0:8:21
HHO Gas provides combustion for an engine without producing harmful exhaust.
check out smacks booster design & a great (&free) PDF which explains everything:
smacksboosters.110mb.com/
smacks youtube:
youtube.com/user/EletrikRide
Duration : 0:8:55
If your a newbie (like me) and dont really know what goes where when it comes to wiring, check out this vid, it might help.
AH
Oh yea here are some links that have some good INFO & articles about EFIE and PWM stuff.
http://www.internationalhydroxy.com/articles/general-information/efie-electronic-fuel-injection-enhancer-described.html
http://www.fuelsaver-mpg.com/documents.html
http://hhohuntsville.com/Hho_electronics.html
http://www.internationalhydroxy.com/articles/general-information/efie-electronic-fuel-injection-enhancer-described.html
If anyone has any more good informational links, drop a line & I will post them here.
Oh and thanks to crob227 for informing that in line resetable circuit breakers you can be purchased at heating and are conditioning supply stores.
p.s. BTW I am not endorsing any products on these sites; just the information they contain. I cannot in all honesty endorse a company or product in which I have not purchased &/or tested.
Disclaimer:
Buyer beware - do some research, shop around and make an informed decision before you purchase anything. I am not liable for anything you do - stated or implied.
Duration : 0:9:30
HHO/efie-and-pwm-wiring-diagram-for-hho-systems#more-226″ class=”more-link”>Read the rest of this entry »
http://alt-nrg.org/
Repost of previous vids, combined two parts down to one. This is the Energy Builders Network prototype cell scheduled to go into production in kit form very soon. We’re just working out the details of the bubbler which will have an automatically reseting blowout mechanism.
Duration : 0:8:6
Please visit my site http://alt-nrg.org/ for latest news.