For more info visit http://www.GreenFuelH2O.com
+++++++++++++++++++++++++++++++++++++++
A look at my new management system handling 21 LPM
Duration : 0:4:5
HHO-gas/20-lpm-hydrogen-generator-hho-managment-system#more-354″ class=”more-link”>Read the rest of this entry »
Conclusion on the mileage tests on my Ram 1500. Two 30.1 mile runs, the first with no O2 sensor extenders with HHO, and the second the truck running stock.
Combined results after all three videos:
Stock: 16.4 mpg
Stock + HHO: 17.5 mpg
O2 Ext’s only: 20.1 mpg
O2’s + HHO: 23.6 mpg
Duration : 0:4:3
Chevrolet 2006 HHR Water For Fuel - HHO Gas Part 2
I am a perfectionist in doing things right the first time. During the demonstration I try to perform the demonstration as if everyone is watching the video was doing it themselves along with me. During my video I try to do things to prevent skepticism. Before I put this welding machine on a trial run on my vehicle I will be using scientific equipment to make sure that there is no sodium hydroxide passing through the tube on a regular basis into the engine. During the demonstration there was a 20 foot hose running from the welding machine to the flashback arrestor an additional 15 foot from the arrestor to the automobile. The flashback arrestor at that moment of time was acting as a fluid separator only allowing the HHO Gas pass through it. In addition I will be checking with the Chevrolet dealership electrical department to make sure that the alternator is putting out enough energy to run my electric inverter taking the power from DC to AC to run the welding device. If we cannot run the inverter to the welding machine that we will have to bypass the AC power supply on the welding machine and go into the DC portion of the machine to perform the same functions as if it was plugged into the AC. Before we do that we would try this simple way first using our inverter to simplify the installation.
Duration : 0:7:49
This video is brought to you by AllgoodAutomation & the Energy Builders Network. I am showing you the functionality of a new PWM Control and the EBN 4N4 Cell. The cell produces about 1.2 Liters per minute with a very light electrolyte concentration. The Control has a voltage detector built in to prevent operation if the supply voltage drops below 13.6 volts. The control is adjustable between 100 HZ and 7 KHZ also with PWM 0-100 duty cycle.
Duration : 0:7:2
HHO/hho-pwm-control-test#more-306″ class=”more-link”>Read the rest of this entry »
Just going over a design for a flash back arrestor. Some people have been asking questions related to flash back arrestors when using a hydrogen fuel cell. So here it is. A very easy technique to implement a simple flash back arrestor using fine bronze wool picked up from a local boating supply store. This will be used in future experiments related to a HHO mini torch, and hydrogen heating applications.
There are three known techniques for flash back arrestors that are proven: fine bronze wool, cigarette filter, and a fine (white) fish tank air stone.
** Please NOTE **
3/8″ Tap is tapered NPT (National Pipe Thread)
This is a safety mechanism that is MANDATORY in every HHO Cell design!
Safety is our top concern. Keep your set-up legit and you can ignite the gas with-out concern of explosions in your hydrogen experiments. That in itself is a accomplishment.
Regards, –sirHOAX–
Duration : 0:8:0
Water is soo powerfull Who needs Oil?!
Open your Mind?
HHO Gas 1 ltr tried to make a rocket but it exploded
VERY LOUD BANG
add 2 parts hydrogen to 1 part oxygen
1ltr bottle and lite
Becarefull
water is soo powerfull Who needs Oil?!
Duration : 0:0:37
Seventh in the series. This Video is reloaded due to playing problems.
I have rebuilt my cell to 5 cells with varied spaces between the cells set up so the negative plates have double spaces and the positives are single.
-ssNssNsNsNs+sNsNsNssNss- and so on, **I did try it in reverse with poor results**
Since current flows from negative to positive my thought was to allow more space close to the source of current and in turn more room for flow. I’m not sure of my results since all my testing so far has been done with the pump running (RIP), should have my pump by Monday at the latest (I hope) and I will run this test again to get a accurate comparison.
On a side note, after yesterdays experiment I have ordered more plates and gaskets from www.fireinthewater.com to use for high voltage testing. If I can get a good result from that then I’ll purchase an inverter an see it that will get my numbers where I want them.
**Extra note** I tried raising my cell up so that the top was near the bottom of my reservior to shorted the return tube height.
Result: good gas flow but almost zero cycling of the electrolyte.
Conclusion: for convection flow a height difference is necessary. However, at a certain point high output of gas will cause the fluid to separate from the gas in the return tube and fall back into the cell.
And I just like the pump.
Duration : 0:7:9
Setup of 
http://www.hybridwaterpower.com. This is an original demo unit we used when we first started developing and testing on-demand hydrogen generation systems. It uses SS drains and creates incredible convection currents along with a decent gas production.
http://hydrogen.mixcat.com