This is an update on my Brick Cell Hydrogen Generator.
Duration : 0:3:37
—-Check It Out—-
For more info visit http://www.GreenFuelH2O.com(Video 44) Simple HHO Gas Filter (HHO, Brown’s Gas, Hydroxy)
This is a video showing my HHO Gas Filter that is a variation of jdcmusicman’s design. It is intended to remove any impurities from the exhausted gas of HHO fuel cells.
All of the parts were very inexpensive and can be purchased from just about any home improvement store.
Duration : 0:1:28
HHO Ram 1500 #16, gas milage tests Part 3
Conclusion on the mileage tests on my Ram 1500. Two 30.1 mile runs, the first with no O2 sensor extenders with HHO, and the second the truck running stock.
Combined results after all three videos:
Stock: 16.4 mpg
Stock + HHO: 17.5 mpg
O2 Ext’s only: 20.1 mpg
O2’s + HHO: 23.6 mpg
Duration : 0:4:3
Chevrolet 2006 HHR Water For Fuel – HHO Gas Part 2
Chevrolet 2006 HHR Water For Fuel – HHO Gas Part 2
I am a perfectionist in doing things right the first time. During the demonstration I try to perform the demonstration as if everyone is watching the video was doing it themselves along with me. During my video I try to do things to prevent skepticism. Before I put this welding machine on a trial run on my vehicle I will be using scientific equipment to make sure that there is no sodium hydroxide passing through the tube on a regular basis into the engine. During the demonstration there was a 20 foot hose running from the welding machine to the flashback arrestor an additional 15 foot from the arrestor to the automobile. The flashback arrestor at that moment of time was acting as a fluid separator only allowing the HHO gas pass through it. In addition I will be checking with the Chevrolet dealership electrical department to make sure that the alternator is putting out enough energy to run my electric inverter taking the power from DC to AC to run the welding device. If we cannot run the inverter to the welding machine that we will have to bypass the AC power supply on the welding machine and go into the DC portion of the machine to perform the same functions as if it was plugged into the AC. Before we do that we would try this simple way first using our inverter to simplify the installation.
Duration : 0:7:49
This is a quick video to demonstrate my Blade Cell Hydrogen Generator. 
I just threw this video together to share some advancements on my Volcano DryCell design.HHO Dry Cell #7, 5.23 MMW
Seventh in the series. This Video is reloaded due to playing problems.
I have rebuilt my cell to 5 cells with varied spaces between the cells set up so the negative plates have double spaces and the positives are single.
-ssNssNsNsNs+sNsNsNssNss- and so on, **I did try it in reverse with poor results**
Since current flows from negative to positive my thought was to allow more space close to the source of current and in turn more room for flow. I’m not sure of my results since all my testing so far has been done with the pump running (RIP), should have my pump by Monday at the latest (I hope) and I will run this test again to get a accurate comparison.
On a side note, after yesterdays experiment I have ordered more plates and gaskets from www.fireinthewater.com to use for high voltage testing. If I can get a good result from that then I’ll purchase an inverter an see it that will get my numbers where I want them.
**Extra note** I tried raising my cell up so that the top was near the bottom of my reservior to shorted the return tube height.
Result: good gas flow but almost zero cycling of the electrolyte.
Conclusion: for convection flow a height difference is necessary. However, at a certain point high output of gas will cause the fluid to separate from the gas in the return tube and fall back into the cell.
And I just like the pump.
Duration : 0:7:9
Scarecrow Labs – 20080803 – HHO Torch at 8 LPM
Testing the performance of the EBN, Inc. (Energy Builders Network) prototype 101 plate electroyser.
Running at 8 LPM output. Had to turn down the production volume just a bit to keep it from blowing out the torch.
Testing the function of D3’s torch at 8 LPM output volume of HHO. This was so much fun I was cutting various stuff for most of the afternoon.
The video is short because I really did not want to bore everyone. But as a cutting torch, HHO rules!
http://www.energybuilders.net
Duration : 0:4:19
Scarecrow Labs – 20080804 – 3.5hp Genset Runs on HHO
Testing the performance of the EBN, Inc. (Energy Builders Network) prototype 101 plate electroyser.
During this test, we run a 3.5hp, 1500va Generator on HHO. Just to show it can be done.
These are the stats:
Engine is a 3.5hp 4-cycle, 87cc
Generator is capable of 1200w continuous with 1500w peaks
Electrolyser is powered from 120vAC house current rectified to 146vDC at 13 amps. Gas volume produced is about 9 liters per minute. It has has 101 316L stainless steel plates in an 8″ x 8″ form factor.
So there is no misunderstanding, no, the generator is not able to put out enough juice to power the electrolyser. Yet.
http://www.energybuilders.net
Duration : 0:6:26
EBN More fun with the HHO Light Saber
D3 and SmartScarecrow join up to work on the small engine project. But you just know they will make some time to play with the HHO torch!
Duration : 0:1:59
HHO SWISS INOX 7 POWERFUL MINI DUAL COIL +MARINE WIRE COIL
Very powerful MINI DUAL COIL for extremely small cells with high production Ideal for a motorbike or modern cars with no space under the hood. 3 mm rod 316L Stainless Steel and an acrylic plate 4 mm thick.
A youtuber gave me the idea to try and use marine wire to make a coil, his suggestion was that that wire has a larger surfacearea.
The wire I used is 4 mm diameter and has a M5 metric thread welded on it’s end so you can tighten the electric cable on it.
As I thought about it I realized that this could also be the solution for those people with no tools. Easy and relatively inexpensive. The water test of this spiral was made without cleansing so the first ignition gave a slow reaction as you will see.
If you get salt water grade wire it will be just great
Duration : 0:7:34
HHO SWISS INOX 8AFTER ONE YEAR’S EXPERIENCE
New marine wire coil, square cell, doble spiral
12 volts battery, stainless steel 316 L marine wire 3 mm (1/8 of an inch) diameter 50 mm, lenghth 100mm
double spiral 3 mm 316 L stainles steel wire and 316 L container
square cell 304 L stainless steel 2 neutrals tubes.
As a conclusion I have to say that for the sake of HHO Gas production, anything you do basically works!
You can reduce electrolite in the distilled water to lower the amp draw of the cell, you can add a PWM and some how you manage to have a workable cell that can fit your personal needs.
But if you are looking into a high efficiency cell, then there are the Stan Meyer cells with tubes and electronics, and the Lawton’s replication of it.
There is the Joe Cell in shandy mode.
There is daddyo44907 with nice, efficient workable cells.
There is EBN Smart Scare Crow and Zero Fossil Fuel with a super cell
And a the top of the expectation list there is the BobBoyce 101 plates cell whit low amps and it has an alledged output of near 100Liters per minute.
Duration : 0:9:57
Chevrolet 2006 HHR Water For Fuel – HHO Gas Part 1
Chevrolet 2006 HHR Water For Fuel – HHO Gas Part 1
I am a perfectionist in doing things right the first time. During the demonstration I try to perform the demonstration as if everyone is watching the video was doing it themselves along with me. During my video I try to do things to prevent skepticism. Before I put this welding machine on a trial run on my vehicle I will be using scientific equipment to make sure that there is no sodium hydroxide passing through the tube on a regular basis into the engine. During the demonstration there was a 20 foot hose running from the welding machine to the flashback arrestor an additional 15 foot from the arrestor to the automobile. The flashback arrestor at that moment of time was acting as a fluid separator only allowing the HHO gas pass through it. In addition I will be checking with the Chevrolet dealership electrical department to make sure that the alternator is putting out enough energy to run my electric inverter taking the power from DC to AC to run the welding device. If we cannot run the inverter to the welding machine that we will have to bypass the AC power supply on the welding machine and go into the DC portion of the machine to perform the same functions as if it was plugged into the AC. Before we do that we would try this simple way first using our inverter to simplify the installation.
Duration : 0:10:17
generator running on hho testing Pt.9
more of the engine running on hho
HHO H2o Hydrogen Oxygen Electrolyzer stan meyer steam hoh injection mpg fuel economy hho ebn pwm pulse
width modulator mosfet current hho regulated electronic diy cell hho alternate energy smack john deere ice
i.c.e. honda mileage hoh booster hybrid electric car solar power science fair geet electromagnetic ou
overunity over unity gas hoh hydroxy water hho waterforgas zerofossilfuel fossilfuel fossil smartscarecrow
allgoodautomation pulsefuelnerd hoh d3adp00l johnarrons arrons bob boyce engine hho joe joecell hoh
brown’s browns oxyhydrogen hoh pfn d3 zero ssc hoh plasma coldfusion hho cold fusion hoh free freeenergy
hho HHO H2o Hydrogen Oxygen Electrolyzer stan meyer steam hoh injection mpg fuel economy hho ebn pwm pulse
width modulator mosfet current hho regulated electronic diy cell hho alternate energy smack john deere ice
i.c.e. honda mileage hoh booster hybrid electric car solar power science fair geet electromagnetic ou
overunity over unity gas hoh hydroxy water HHO waterforgas zerofossilfuel fossilfuel fossil smartscarecrow
allgoodautomation pulsefuelnerd hoh d3adp00l johnarrons arrons bob boyce engine hho joe joecell hoh
brown’s browns oxyhydrogen hoh pfn d3 zero ssc hoh plasma coldfusion hho cold fusion hoh free freeenergy
hho
Duration : 0:8:52
Engine Running on Hydrogen / Oxygen HOH HHO
http://www.hohcells.com Tests conducted on 2.4HP petrol engine (generator) using made on demand HOH. Engery input 1.3kW from mains power engine RPM 2200. Engine is started on Petrol, then fuel is switched off. Petrol in carby is exhausted after approximately 2 minutes 30 seconds. If you listen you can hear the pitch and RPM change when petrol runs out
Duration : 0:9:54